Beginner's Plumbing: What You Need for Bathtub Installation
Beginner's Plumbing: What You Need for Bathtub Installation
Blog Article
Just how do you feel on the subject of How to Install a Bathtub?
Installing a bathtub isn't precisely rocket science, however it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bathtub with a new one is also a moderately challenging task. If the old tub is conveniently available, the project can move rapidly; if you have to open a wall to eliminate the old bathtub as well as position the new bathtub, the task is much harder. In either situation, the job is within a house handyman's skills, although you will certainly require an assistant to vacate the old tub as well as embeded in the new one. Ensure you have qualified on your own for the task as well as fit trying it. As opposed to hiring a specialist to take control of a halfway-completed job, it is much better to consider using one before you begin. Opportunities are you might require an expert plumber to make tube links.
This post will certainly aid you install a new bathtub in your bathroom if you have already purchased a new bathtub and don't require to transform the arrangement of your previous water pipelines.
Your tools and product list need to comprise the following:
Preparing for the Installment
Firstly, the sustaining frame provided with the bath should be fitted (if needed) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the faucet comes with a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps system to stop stress on the bath tub.
Fit the versatile faucet ports to the bottom of both taps using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its last setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The procedure of removing the existing taps can be fairly problematic as a result of the restricted access that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a towel ready for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have been removed, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing substance.
Prior to going on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.
Mounting the Bath tub
Utilizing both wood boards under its feet, place the bath tub in the required setting. The wooden boards are valuable in evenly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto 4 little factors.
The next goal is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the level and also adjusting the feet on the bathtub until the level checks out level.
To mount taps, fit the bottom of the outermost versatile faucet connector to the appropriate supply pipeline by making a compression join; after that do the very same for the other faucet.
Switch on the supply of water and inspect all joints and also new pipework for leaks and also tighten them if needed. Load the tub as well as additionally check the overflow electrical outlet as well as the typical electrical outlet for leakages.
Finally, take care of the bath paneling as defined in the maker's user's manual. Tiling and securing around the bathtub needs to wait up until the bathtub has been used a minimum of when as this will resolve it right into its final setting.
Fitting New Taps
If the tails of the new taps are plastic, then you will require a plastic port to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the mounting opening in the bath/basin making certain that the washing machines are in place in between the faucet as well as the sink. Safeguard the tap in place with the manufacturer provided backnut. Once the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The former type should be attached to the faucet ends initially, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, creating the water to pass through the wall surface in between the bathroom and also the tiling, resulting in issues with dampness and also possible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your fixtures and fittings. They are sold in tubes and cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to allow for the movement experienced when the tub is in use. The sealer can crack relatively early if you do not take into account this activity prior to securing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally conveniently offered on the marketplace. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very drawn to Tools You Need to Install a New Bathtub and I am praying you enjoyed reading the entire page. Loved our write up? Please share it. Let other people locate it. Thank you for your time. Visit again soon.
For top results, contact! Report this page